|
 |
 |
Patience pays off! |
10/31/2023 |
| I replaced the sights on my two SR22 pistols recently, using these Williams sights. The original sights were fine, but after a few years, the plastic rear sight began to move around on the slide.
These Williams sights are a worthwhile upgrade, the fiber optics light pipes make the sights really stand out. The front sight does require careful fitting before driving it home into the dovetail cut. I used a diamond sharpening stone with four different grits, and a small, triangular jeweler's file. Be patient, trial fit many times to get it "juuuuuust right."
While you give up screwdriver adjustable left/right adjustment, the sights are easily adjusted, remain adjusted, and offer a much nicer sight picture. |
| - Dave Shema, IA |
| |
|
Sr22 front and rear sight. |
6/21/2023 |
| Easy peasy! Took me 5 minutes to install, my only complaint is they didn't send the small Allen wrench that is required to tighten the new site in place and required to adjust the rear sight..The Allen wrench is extremely small. If you do not know what you are doing, pay someone that does. The sights are a amazing addition to the sr22 pistol,don't turn something great into a bad situation or a bad review because you don't know what you are doing.i have put these williams sights on 4 firearms now with zero issues. |
| - Avid Sportsmen, UT |
| |
 |
Excellent sights |
1/4/2022 |
| Slight difficulty putting in but they install right to left on both rear and front slide. They claim to have up/ down and right/ left 'click' adjustment but i only can figure out the up/ down. I'm shooting slightly right so I'll have to push rear sight slightly left. |
| - M H, CT |
| |
 |
Does not fit |
7/22/2020 |
| I thought it was expensive but I was willing to pay it and excited to have this on my SR22. I think sights should be tight, otherwise theyre going to be moving on you; with that said, these sights do NOT fit the Ruger SR22. I understand some fitting may be needed sights on some guns, but again these sights, just are not made to fit a Ruger SR22. |
| |
|
Good |
1/14/2018 |
| Good |
| - Katrell West, MS |
| |
|
Foresight doesn’t fit. |
10/28/2017 |
| This is a terrible product, do not buy! Sight does not fit, extensive grinding is required to make fit into front sight slot. |
| - AK, NC |
| |
|
Nice but not worth the expense |
7/3/2017 |
| The sights themselves light up and acquire very nicely and I rate that aspect highly. However, the difficulty of installing the sights did end up requiring me to pay the local gunshop to complete the installation thus costing me an additional $25 beyond the cost of the sights themselves. Also not pleased with the lack of windage adjustment on the rear sights even though it is advertised as being click adjustable. Apparently that only applies to elevation. |
| Tito |
| |
|
rear Sight Fell Apart |
3/7/2017 |
| The red tubes in rear sight fell out after 3rd use. Poor quality, wouldnt buy again. |
| Jay |
| |
|
Do not fit |
2/8/2017 |
| Got a set today and they do not fit, they are not machined very well. Would not ever purchase another set |
| OH |
| |
|
Great sights! |
2/6/2017 |
| Minor fitting needed a few minutes with a file is all
Nice bright sights easy to line up quickly much better than the original! |
| Derek Q |
| |
|
Love Em |
1/21/2016 |
| These sites are fantastic. A great improvement to my already great Ruger. They just light up. It takes a little bit of patients to install them but the time spent is well worth it. |
| Bungie |
| |
|
They dont fit. |
12/15/2015 |
| These sights simply dont fit. You can alter them to make them fit, and maybe it will work. Overpriced junk. |
| - T W, ME |
| |
|
Great upgrade to stock sights |
3/5/2015 |
| I put these on my SR22 and there is simply no comparison. Visibility is fantastic in all but the dimmest light. Installation was a breeze. I used a punch and, out with the old, in with the new. Took me just two tries - with no equipment other than a screwdriver - to sight them in. |
| IL |
| |
 |
Sr22 sights |
10/18/2014 |
| Nice sights if you can get them to fit.
Took some filing on the sights to fit. Both front and rear.
Used a micrometer and the rear was .007 too wide and the front I dont remember. Would rate higher if it F I T
Waiting for trijicon to produce a set. Just a comment, I have change sights on sigs, glocks and NEVER had a problem.
Room for improvement |
| - Joe B, NY |
| |
0
